Exactly How to Set up a Tub: Install an Acrylic Tub and Bathtub Surround
Exactly How to Set up a Tub: Install an Acrylic Tub and Bathtub Surround
Blog Article
They are making several good points about How to Install a Bathtub Yourself in general in this great article on the next paragraphs.
Mounting a tub isn't specifically brain surgery, yet it does need strong plumbing, carpentry, and in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough task. If the old tub is conveniently accessible, the job can move immediately; if you have to open up a wall surface to eliminate the old bathtub as well as place the new tub, the task is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub as well as embeded in the new one. Make certain you have qualified on your own for the work as well as fit attempting it. Instead of working with a contractor to take control of a halfway-completed task, it is better to take into consideration employing one before you start. Opportunities are you may require a specialist plumber to make tube connections.
This short article will certainly help you install a brand-new bath tub in your bathroom if you have already acquired a new tub as well as don't require to transform the setup of your previous water supply pipes.
Your tools as well as product list should make up the following:
Preparing for the Installation
First of all, the sustaining framework provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to make sure that if the tap comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be fitted in its last placement.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome because of the restricted gain access to that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Prior to proceeding to fit the new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using both wood boards under its feet, position the bathtub in the needed setting. The wooden boards are practical in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub till the level reviews degree.
To install taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system and also examine all joints and also brand-new pipework for leakages and also tighten them if essential. Fill the bathtub and also check the overflow outlet as well as the regular electrical outlet for leaks.
Finally, repair the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bathtub should wait until the bathtub has been utilized a minimum of when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making certain that the washers are in place between the tap and the sink. Secure the tap in place with the producer offered backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former type should be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to crack an inflexible seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing issues with moisture and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and installations. They are offered in tubes as well as cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before sealing, to enable the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading about How to Install a Bathtub Yourself? Give a comment further down. We'd be pleased to see your insights about this page. In hopes to see you back again in the future. Appreciated our posting? Please share it. Help somebody else discover it. I enjoy reading our article about Installing A Bathtub.
Book Your Installation
Report this page